The problem with fan heaters is that they blow dust around ![]()
Buy a Dyson and end the dust ![]()
Other much better vacuum cleaners are available… ![]()
That sucks.
Hmm, a few years back I would agree, bits broke off all the time and then there was the necessary ear defenders
however against some of the competition they lead them. The sealed HEPA containment is great, not a single 1 point increase in the PM’s on my meter when testing in the room. Henry by comparison would probably set off an asthma sufferer.
Leroy Merlin had a big stock of different plug in radiators when I went in last week for an extension lead. Don’t think they will hang around for long!
No.. not on that type of device .. .They are crude ..A radiant coil of wire has 1 or 2 KW of power going through it and a fan blowing the air out .any obstruction will make the wire go red hot ,and start melting the plastic housing .Thermostats are not a feature of this technology . Temperature control is of the one coil or two variety and fan speed 1 or 2.
The oil filled radiator are much safer for that reason they do have thermostats .and in some cases will have sufficient metallic surface area what even were the thermostat to fail, and the 1KW output continue the temperature of the surface would never exceed the boiling point of the oil , before a fuse melts
Must be some old units you are referring to, not seen any without thermostatic adjustment. My test for tomorrow is to throw a towel over the old one I have been using and see what happens
Indeed. Our £15 fan heater has a (working) thermostat, as do the 15 euro fan heaters in our French house. The days of non-thermostat controlled fan heaters finished years ago.
Possibly a power controller , rarely a thermostat
Nope, a bi- metallic thermostat.
When you do your test ..please do it on a ceramic tiled floor
How would a power controller switch the heater on and off based on room temperature? Serious question.
Such is my confidence in bi metallic strips I just put it down where I was working and chucked a towel over it both on the 1kw setting and the 2kw, no worries.
A serious question deserves a serious response. To sample room or air temperature you need a thermostat well removed from the source of heat and this is achievable on an oil radiator or one of those wall mounted convecter heater with ceramic cores. Even my hot air blower Dimplex Optiflame chimney insert has the space to have a thermostat .But that is a 300 euro unit , with a lot of steel not a 15 euro plastic casing
But the oil radiator I have about 1M away has the thermostat directly on the end of the radiator (probably near the top inside the electronics, though I’ve not had the case apart to look). That’s a 25 euro unit.
With a fan heater, it would be easy to put the thermostat in the stream of moving air drawn in to feed the fan - pretty much ideal really.
And that would be lethal if the towel dropped over the output ..No air flow ..fast heating, fast melting… The heating wire is naked nickel steel wrapped around a ceramic form and goes red hot when there is air flow ..with no air flow it goes white hot. Look I have made my case no point in prolonging this.
The oil heater is different .The heating element is almost certain an enclosed rod located in the bottom of the radiator so the thermostat is sampling the surface temperatures on the fin
I thought I had proved that today, shuts down safely before the towel gets too warm. Towel blocked inlet and outlets
I’m not sure I recall a standard domestic fan heater where the element is actually glowing red in normal use. Heat gun, maybe; toaster - definitely; but not a fan heater.
Anyway they have thermal cutout switches on/close to the element so if the fan stops or the airflow is blocked they will have the power to the element turned off. Could they still start a fire despite this - possibly if the right set of conditions aligns itself, but modern ones are fairly safe. Some also have tip switches so they get turned off if knocked over.
I’d say, breathe in the dust while emptying it ![]()